Home News Fix: To Fix Hard Disk Read Error: Press Ctrl Alt-Start

Fix: To Fix Hard Disk Read Error: Press Ctrl Alt-Start

47
0

 

“An error occurred while reading the hard drive” is a common error that occurs and indicates that Windows detects a problem with the hard drive or that the hard drive is not reading. Restart your computer by pressing Ctrl Alt Del. The error could not be fixed and you still get the same screen.

 

 

If you have a problem using your computer and receive an error message if it crashes, hopefully this message indicates the cause and can be resolved accordingly. However, this is not always the case, and the message can be quite general and repairs are not straightforward with a clear place to start troubleshooting.

Unfortunately, there are many errors on your system that seem simple but lead to the same problem. The error message is not specific enough to make a clear decision on what to do next.

Some time ago I had a problem with my computer, and after some strange things happened, for example, the CD-R did not burn and the computer was very slow to respond, I decided to turn it off and leave it for a while. at permission. When I ran it the next day I got an error:

An error occurred while reading the hard disk. Press Ctrl Alt Del to restart.

The BIOS recognized the hard drive without any problems. After extensive research on the internet and forums, no one hasThere was no exact solution to this problem, and there seems to be no one solution that is better than the rest.

< / p>

To make matters worse, there are so many different ways to fix this error that it can take days to fix them. And to make matters worse, a hard drive read failure might not mean the problem is with the hard drive itself! Also, there seems to be as much software as there are hardware reasons.

Here are some of the possible solutions we used to fix the hard disk read error. Press Ctrl Alt Del to restart the problem.

1. Check your memory

This is not often mentioned on the internet as a solution to the disk read error problem, but believe it or not, it was my problem. I used a tool called Memtest86 and ran some tests on my RAM and it found problems. After experimenting with different sticks and RAM slots, I finally discovered that my RAM slot 2 was damaged because the sticks in the other slots did notWe got great.

Since this is a simple non-destructive test that does not require touching the hard drive and risking further damage to it, it is recommended that you try it first. It may sound strange, but in fact, memory problems can be the cause of many different errors on the system, where RAM testing may be the last thing you think about.


2. Try the player on another computer

As we said before, people have reported on the internet that they associate the problem with faulty video cards, modems, motherboards, and even power supplies, even though this problem looks like a problem – a simple hard drive problem. The easiest way to fix this is to remove the hard drive and connect it to another computer, or connect it to the same computer via an external USB port. If you run it after an error, or can easily access all your files, then the problem is most likely related to other hardware on your computer.

Unfortunately When this happens, finding faulty hardware can be a trial and error process by removing or replacing what you can, although the next possible fix is ​​pretty straightforward.

While the drive is connected in another way, it is recommended to run a scan with HD Tune to check for bad sectors. Regardless of whether HD Tune has problems or not, you should also run “chkdsk driver name: / r” on the command line while you have the option, or use a portable tool to do it for you.

It is also recommended to back up files or the entire disk while the disk is available.


3. Check / replace cable

While I have not seen SATA cables fail (but obviously they can fail), sometimes faulty IDE cables can cause problems such as hard drive read or write errors, as well as optical recorders. If you have spare cables, you can either replace them or disconnect the current cables, inspect for damage, and then reconnect them if you’re happy with that…. Also try using other SATA or IDE ports if possible, as there is the potential for port damage.

If, after installing a new drive, an error occurs while reading the hard drive, make sure the hard drive is connected to the primary connector (end of the cable). If possible, set the hard drive jumper to “Master” instead of “Cable Select”. Also try not to connect the secondary (slave) device to the same cable, if you have one.


4. Reset / Update BIOS

In rare cases, resetting the BIOS to default settings may resolve the issue. You can usually enter BIOS by pressing Delete or F2 etc. during the boot process. It should be possible to reset the settings to their default values. Find an option similar to the one shown in the image below. Otherwise, you can remove the BIOS battery for a few minutes to reset it. If you cannot access CMOS because it is password protected, you can easily reset it from Windows using CMOS De-Animator.

It is also reported thatupdating BIOS to a newer version works especially on laptops.

We have several other possible solutions to the page 2 read error

Why Is There A Hard Disk Read Error?

The actual cause of this error varies from computer to computer, from hardware problems to software problems. This section lists the most common causes of hard drive read errors.

Computer hard drive is failing

In most cases, a failure to read from a hard drive indicates damage. If the boot sector of the hard disk is damaged or there are bad sectors in the system partition, then the system freezes with errors.

No bootable hard drive

Sometimes a hard drive read error before booting occurs because the computer is reading the wrong boot hard drive. If the bootable hard drive is missing or the bootable hard drive is not configured correctly, the system will not boot normally.

Damaged hard drive cable

The IDE cable is biga piece of twisted cable in your computer case that is responsible for connecting the hard drive to the motherboard. Sometimes, incorrect or loose IDE cables can cause hard drive read or write errors.

BIOS setup issue

In rare cases, a hard disk read error occurs due to incorrect BIOS settings. If any BIOS updates are available, they should be updated carefully.

MBR corrupted

Another common cause is incorrect or invalid setup of the Master Boot Recorder. Moreover, corrupted MBR configuration can be caused by virus attack, power outage, bad sectors, etc. Also, incorrectly configured partition table can cause this problem.

Sudden power failure

disk read error has occurred press ctrl alt del start

An improper system shutdown can damage your computer’s files and hard drives. This usually happens when the power is accidentally cut off or the system must shut down to terminate a program that is not responding. After a computer crash, Windows checks the file withSystem and hard drive at startup to check and fix problem files.

Operating system problem

An incomplete or incorrect installation of Windows also leads to this problem; For example, if DLL files are missing on the system or some system registry files are damaged.

6. Rebuild MBR

Besides BIOS, it is likely that the MBR is the cause of this error. The Master Boot Record (MBR) is the portion of the hard drive that contains the Master Boot Code, digital signature, and partition table. Hence, the MBR is also involved in the startup process. If any problems are related, it will cause startup errors. In this case, you need to restore the MBR.

You can do this using third-party software or from your Windows installation disc. However, since this procedure is a little complicated, it is recommended that you use an installation disc.

 

 

How do I fix disk read error in Windows 10?

Follow these steps to fix hard drive read error on Windows 10
  1. Step 1. Turn off the system and let it cool down.
  2. Step 2. Reset BIOS.
  3. Step 3. Check the hard drive / SSD cables.
  4. Step 4: Check your RAM.
  5. Step 5. Use Windows recovery / installation media.
  6. Step 6: Check the disk status and restore data.

Can’t get past Ctrl Alt Delete screen?

What if my computer freezes at CTRL ALT DEL?

  1. Repair your graphics card / graphics card driver.
  2. Perform a hard reset.
  3. Perform startup repairs.
  4. Disable quick start / start.