Approved

  • 1. Download Restoro
  • 2. Open the program and select "Scan your computer"
  • 3. Click "Repair" to start the repair process
  • The software to fix your PC is just a click away - download it now.

    You may encounter the samsung s8530 error ffs write error message. Coincidentally, there are a number of steps you can take to fix this issue, and we’ll get to those shortly.

    Approved

    The Restoro repair tool is the solution for a Windows PC that's running slowly, has registry issues, or is infected with malware. This powerful and easy-to-use tool can quickly diagnose and fix your PC, increasing performance, optimizing memory, and improving security in the process. Don't suffer from a sluggish computer any longer - try Restoro today!


    SAMSUNG WAVE II S8530 FIRMWARE MANUAL

    ==================================1. Kies 2.0 must be installed 2. Close Kies 3. Go to “Download Mode” – turn it near the phone, hold down the “Volume Down” + “Camera” button, and hold it, switch the phone to a request. On the screen, the inscription is displayed in blue in download mode. 4. Run the flasher (Multiloader 5.65). 5. LSI, then check the boxes next to Boot Change and Full Download. 6. Next, you need to select the following information (we take all the files from any unpacked firmware you downloaded: – Boot – Select the BOOTFILES.das directory (Specify folders, files are not explicitly specified here) – Amms -amss.bin – Apps -apps_compressed.bin – Rsrc1 – Rsrc_S8530_Open_Europe_Common.rc1 – Rsrc2 – Rsrc2_S8530_Open_Euro_Common (Low) .rc2 Factory – FS Factory – Fs_S8530_Open_Europe_Common.ffs – CSC – CSC_S8530_Open_Europe_Common.ffs – Le CSC mode – CSC_S85 -CSC_Open_Europe download CSC_S8530_Open_Europe is in the “General” on the other hand, and in anticipation of driver installation, if usually a lot of things are installed, then the mobile port number should appear in the “port” mark (if not, then we will solve the problem with installing drivers.) there is on the usual seven, everything worked the first time, the antivirus did not turn off, I hope oftenall Rich teag is over, below is the port number to which it is connected, and the exact program writes “Done -“. I had another inscription “wave 37”, but it was explicitly flashed 9. When the port is determined, press And “Download” we look at any firmware process. This process may take about 10-15 minutes. At the end of the firmware process, you will have the inscription “All files completed” in your blinker. After that, the phone will automatically reboot.====================================================================================================================================================================================================================================================================> After each charge of phone you have to direct make presetting : 1.

    MANUAL FOR SAMSUNG Firmware WAVE II S8530

    ==================================1. Kies 2.0 must be installed 2. Close Kies 3. Give smart diet advice in “download mode” – turn on the phone below, press and hold the “Volume down” key + the “Camera” key, and keep – pressed on the phone the amount. The word Blue in download mode may appear on the screen. 4. Run the flasher (Multiloader 5.65). 5. LSI, check the special boxes next to Boot Change as Full Download. 6. Then we go in and select the following formats (we take all the files of this special unzipped firmware The ones you downloaded: – Boot – select the BOOTFILES directory (specify the folder, the files will most likely not be listed here) – amms -amss. Bin – Program apps_compressed.bin – Rsrc1 – Rsrc_S8530_Open_Europe_Common.rc1 – Rsrc2 – Rsrc2_S8530_Open_Euro_Common (low) .rc2 plant – FS Plant -Fs_S8530_Open_Europe_Common.ffs – CSC – CSC_S8530_Open_Europe_Common.ffs – CSC – CSC_S8530_Open_Europe_Common.ffs – CSC – CSC_S8530_Open_Europe_Common.ffs – CSC – CSC_S8530_Open_Europe_Slav .cotasc – SHP App.€ .APP fshp 7. Connect the number to the computer (it is still in “boot mode” and waiting for drivers to be installed. If something is installed normally, the number of ports should appear in the “Port” section (maybe no, now we are solving the issue with installing drivers) I do it first on s ept usually, the antivirus did not turn off everything in general ok. Then the port number to which the phone is connected is displayed below, and each program writes “Done -“. I had a different Zimmer inscription ) “Welle 37”, but often flashed 9. When the port knocked, press And “download”, generally look at the flashing process. This process takes about 10-15 minutes. Toward the end of the flashing process, the flashing lights may appear “All files completed”. After that, the phone will automatically reboot.=======================================Before everyone has charged the phone, you need to step back to pre-configure: 1.

    The software to fix your PC is just a click away - download it now.