Table of Contents

This user manual will help you solve your Winegard TV antenna problem.

Approved

  • 1. Download ASR Pro
  • 2. Open the program and select "Scan your computer"
  • 3. Click "Repair" to start the repair process
  • The software to fix your PC is just a click away - download it now.

    Step 1. Turn on the new wall switch (amplifier) ​​and make sure each of our lights is on. (It may be red or green depending on the model.)

    HD antennas generally do not corrode because this cable is shielded on every channel and is not affected by real elements. The hd8200p vineyard at Asset is over 14 years old and is still in excellent condition.

    Step 2. Walk up to the cross roof of the RV and remove the coaxial cable from the antenna head. Check for corrosion.

    Step 3. Use a DC voltmeter or, if desired, a 12V DC test light to measure the voltage on the coaxial cable. Place a ground wire (if ) on the outside of the jack, not forgetting the positive wire (red) on this center wire of the coaxial cable. It should measure about 12 volts DC.

    Step 4. The presence of what is already there indicates that the wall plate switch is working properly and the coaxial cables are generally good. Most likely the problem is that the type of amplifier inside the antenna head is faulty. The antenna head needs to be modified. We do not recommend that you try to replace or repair the amplifier board. The antenna head has been ultrasonically welded to prevent it from collapsing while the vehicle is in motion. If you break this weld, my husband and I are not responsible for any damage that may occur.

    winegard tv antenna troubleshooting

    Step 5. If everyone doesn’t have a 12 volt antenna head, then you need to measure the top and back of the wall switch on it.

    Your lines may be wobbly. When clients have cables disconnected, in most cases they will not receive any signal or intermittent signal. So make sure your friends are snuggled up to the TV and antenna. Also, when checking some connections, pay attention to the cables to ensure they are not kinked, twisted, or defective.

    Half a dozen steps. Once on the wall, remove the switch from the wall panel and disconnect the coaxial cable leading to the antenna housing from the coaxial connector installed on the board on the wall switch. Nowthis connection is on your current right side as you are no doubt looking at the back with coaxial connectors.

    Step 7. Measure the voltage across the outlet with a switch through the outlet. It should be about 12 DC voltage. NOTE. Do not insert a test lead from a meter or an evaluation lamp into the coaxial connector, otherwise insert a small diameter wire or perhaps open a paper clip and plug it into a power outlet. The large size of the probe will definitely affect the connector. Place the ground wire (black) on the outside of the new outlet, and the positive (red) on the wire or paper that you inserted earlier.

    Step 8. If at this point you have voltage, the problem is in the coaxial cable between this height and the antenna head. Most likely plugs into the coaxial connector under the roof baseplate. To access this accessory, remove the barrel from which the barrel clip pulls the panel to the floor, as well as the super coaxial cable, until the connectors are accessible. Inspect most connectors for corrosion and if necessary and replace.

    Step 9. If you cannot power the coaxial lift on the back of the wall panel and the lights are on, the wall switch is expensive and needs to be replaced.

    Step 10. Other concepts and tips.
    A. Before breaking the bottom plate seal, replace the good piece of the identified coaxial cable between the head and the wall plate by passing it through the door or window of the box and see what my problem is.
    B. If there is a red light on any part of the wall panel, check the back of the coaxial input connector to make sure each pin is not shorted or bent for connection. He should stretch the muscles back. It’s new, with a small black wire soldered to it.
    C. If your facility has voltage where it is and most of the light is off, then it is likely extinguished.
    D. If the moderate turns on and off again after a few seconds, it may short circuit our coaxial cable or head antenna. To find out which one, turn off firstthose are an agreement from checking the head and the whole world. If it stays in your head now, it will not be received. If you think that freeze frame is disappearing, keep your forehead disconnected and then unplug the coaxial cable from the wallplate switch and indicator light again. If it is off now, it is likely that there is a short circuit in the coaxial cables.
    E. If the light comes on but you don’t have time to turn on the cigar outlet, check the connector on the back of the cigar outlet for plastic melting problems. This is actually caused by using an outlet designed for devices other than a gaming TV, or an outlet that was plugged in when it was unplugged for use.
    F. If you have multiple VHF channels (2-13) and not all UHF channels (14-82), make sure your TV is set to ANTENNA and not CABLE. Improved menu for your own TV. The terminology changes depending on the specific one.
    G. To determine if there is a problem with the main coaxial cables from the wallplate to the TV, select a cable with a known x Good quality from the front connector that connects to the wall panel directly to one of the connectors installed in the TV program.
    H. To test the connection of the input wire to the outside of the RV, use the output of a particular VCR with tape known to be on it.
    I. Worm gear and screw jack should be lubricated every 3 months to ensure up to 6 months of operation, depending on climate and driving conditions. Failure to follow this strict rule can result in hard starting and damage or chafing of the gears. A good quality spray silicone grease will work very well. DO NOT use aerosol solvents such as WD-40.

    winegard tv antenna troubleshooting

    If you find that the antenna head or main switch on the wall panel is defective, most likely send it to Winegard Technical Support for repair. If they are less than two years old, these types are covered by a warranty. If they are over two years old, include a receipt with the credit card number with the expiration date on the refundthose. The fee for the 30 antenna head is $ 15 and the wall button is $ 14 twenty-seven cents per day. Write a check to Vinegaard. Please include a note about the problem and your phone number. Submitted by: Winegard Company
    Technical services
    3000 Kirkwood Street
    Burlington, pcs. 52601

    Approved

    The ASR Pro repair tool is the solution for a Windows PC that's running slowly, has registry issues, or is infected with malware. This powerful and easy-to-use tool can quickly diagnose and fix your PC, increasing performance, optimizing memory, and improving security in the process. Don't suffer from a sluggish computer any longer - try ASR Pro today!


    The software to fix your PC is just a click away - download it now.