If you get the xp pro blue screen death error code, today’s guide is here to help you.

Approved

Bluish screen error with directives “0x00000050” (PAGE_FAULT_IN_NONPAGED_AREA) may be caused by unsafe data on the hard disk, incompatibility with the graphics card drivers installed with Windows XP, or some other reason.

Blue Screen of Death or possibly BSOD occurs when a critical hardware component or Windows kernel failure interferes with the normal operation of the system. The system shuts down to prevent damage and more, leaving an area filled with white diagnostic text that is often difficult to read. Incorrect installation or incorrect drivers can often lead to BSODs, as can faulty disks and corrupted operating system movies. Sometimes, simple power surges can damage your system.

Step 1

If your site displays BSOD, just look at the third line of text at the top of the screen to see why your system cannot boot normally after shutdown. The simple reason is an “unmountable disk volume” which could indicate a problem with your hard drive orand the structure of the story on it. Another common problem is “page failure in an unsupported region”, which unfortunately can indicate damaged computer files on the hard drive or faulty memory modules. Keep this in mind if a specific driver for a laptop or computer is mentioned.

Step 2

Close the program and unplug the power cord, I would say the one from the wall. Hold the power button for a few seconds to drain the remaining power from the motherboard. Leave the system on for 10 minutes. Minor current spikes sometimes cause BSODs, and discharging the circuits for a few minutes can fix the problem.

Step 3

Reconnect the power cords and restart your computer. Press F8 until you return to the Windows boot options menu. Select “Safe Mode” and press “Enter”.

Step 4

5

Delete

Steps Any Hardware Or Software Already Added If The BSOD Occurs Shortly Thereafter.

Step 6

Approved

The ASR Pro repair tool is the solution for a Windows PC that's running slowly, has registry issues, or is infected with malware. This powerful and easy-to-use tool can quickly diagnose and fix your PC, increasing performance, optimizing memory, and improving security in the process. Don't suffer from a sluggish computer any longer - try ASR Pro today!

Click any Windows button, Start you get Run, type eventvwr (by Stepwise without quotes) and press “Enter”.

Step 7

Click System, then Source in a column heading to sort the factors in that category in alphabetical order.

Step 8

Look for errors or warnings in the Hard Drive source. If you see it, the hard disk pump might be defective.

Step 9

Click the Windows Start button, select Run, Classify cmd and press Enter to open a Command Prompt window.

Step 10

Step 11

Press “Y”, enter the “Enter” log, type “Exit” and press “Enter” to close the window.

Step 12

Restart the current computer and run the hard disk check utility. This Windows resource will scan your hard drive for inaccuracies and fix bad sectors and information errors. This process can take an hour or more.

Step 13

Step 14

Click the Windows button, select “Start”, select “Run”, type “eventvwr” and “Enter” for multimedia. Click Application Log.

Step 15

Click Time to sort items in chronological order, often starting with the most recent.

Step 16

Double-click the maximum current log listed as “winlogon”. This is your disk check report.

Step 17

Check the information in the Description field. All bad sectors are written to the event log. See if you can replace your hard drive as soon as possible, even if Check Disk was able to fix it. Bad sectors are sometimes a sign of impending hard drive failure.

I feel like a newbie here and desperate because some are helping me with my Windows XP Pro machine. (I think I’m getting SP2, but can’t be sure; 100% it’s been many seconds since I used this computer.) Sorry in advance for the length of the message; I never know what to do here together, I have tried several things already and would appreciate any help you could give me.

I haven’t normally used this computer for the past few years, and in the few months I’ve tried to use it lately, I get a blue computer screen that says:

STOP: c0000221 Checksum of bad image
The ole32.dll image may be damaged. The header checksum does not match your calculated checksum.

It usually happens that after a custom Windows XP logo appears (with a “boot” bar), I cause a blue screen that blinks so quickly that I cannot read it, at which point the computers are restarted. I will most likely keep the blue screen by pressing F8 a few times as you will see the computer start up and then see the entire Disable Automatic Restart on System Error menu.

Also, from that opening F8, I tried to boot in a specific mode below, but the same problem occurs when it is usually the XP logo / boot screen and then a blue flash screen and restart:
– acceptable mode
is the last known professional configuration
– debug mode

I was advised to return to this page (https://support.microsoft.com/en-us/?Product=winxp), but I’m a little confused, also because I don’t have your Windows 98 disk or ME. (This workstation came from Dell in 2000 via Windows 98 and I installed XP a year or two later from the last Windows XP Professional CD, used and all computers successfully over the next few years, installed the service pack and it could have been two Along the way I can’t find a way following yours For instructions, create a Windows 95 boot floppy from MS-DOS, because I am not using 98 with this method.

other cards along the way suggested going into “repair” mode by plugging in my Windows XP computer. I followed the instructions given here correctly (http://www.michaelstevenstech.com/XPrepairinstall.htm without saving my stats because I cannot access this OS. I did have a choice.) Came to point 3 stated For more information, see the “XP Repair Install” section.

“The installer did not find any hard drives added to your computer.

“Make sure all highly complex hard drives are powered on, properly connected to your computer, and that the hardware configuration of the hard drive is still correct.” This may require running diagnostics or the installer provided by the manufacturer.

In 2000, each of thetheir computers were equipped with a 20 GB hard drive. In early 2005, a friend of mine installed a new 250 GB hard drive that will replace the 20 GB (20 GB may have disappeared.) The 250 GB drive appears above the list of drives on the entire black and white BIOS screen that appears at the start of almost every reboot. …

So now I don’t know what to do! Is there only one way to get a new hard drive, install XP on it, and then run my current hard drive as a full slave to extract the ring folders from it?

Jake Steere

Related posts:

How To Fix Apple Computer Blue Screen Of Death Troubleshoot And Fix Reboot After Blue Screen Xp Easy Way To Fix Driver_irql_not_less_or_equal Blue Screen Windows 7 How To Fix A Blue Screen After Windows?