Table of Contents
Approved
You should read these troubleshooting tips when you get a cool spyware blaster error message.
Most cardio equipment problems can be resolved by by doing the following. Look for the appropriate warning sign and
follow the steps you wrote down. If you need more help, see the first page of the previous manual.
SOLUTION: a. Make sure our cable is plugged into a good surge protector and plugged into a specific surge protector.
is plugged into a properly connected outlet (see page 12). You will most likely be using a single outlet surge suppressor that meets all specifications on page 12.
b. Once the power cord has been plugged in, make sure our dongle is inserted into your console.
If the treadmill is also plugged into an electrical outlet and the power source is still not turned on, make sure the console key is turned on and the reset / off circuit breaker has not tripped. When the switch operates, set the switch to the “Reset” position. Currently, check the reset / stop breaker if operation stops during operation.
Treadmill frame next to power cord. If the
switch protrudes as shown, the
circuit has tripped. To reset the world circuit breaker, wait five minutes, then press the circuit breaker again.
SOLUTION: a. Check the reset / stop circuits (see illustration above). If the circuit breaker tripped normally, please wait
b. Make sure the power cord can be plugged into a power outlet. When the power cord is plugged in, unplug it
in. Take out the key h from the space between the console. Return the key to the main part of the console.
d. If the treadmill still doesn’t work, read the hats in this manual.
PROBLEM: Device screens remain on when you remove the key from the console
SOLUTION: any. The console has a simulated display mode that you can use while displaying the treadmill
charge. If the indicators light up when the key is removed, the display mode is activated. To turn off the rotation demo mode, perhaps hold down the stop button for a few seconds. If the displays are still on, turn off
INFORMATION MODE on page 29 to turn off Simulation Mode.
POWER CABLE. With the help of a second person
carefully tilt the Uprights (74, 78) down.
There can always be two # 8 x 2 “screws at the bottom (105).
Abdominal cup (73). If applicable, remove them. NOTE: One 5mm (13 cm) or more Phillips screwdriver is not required. Raise racks in a single upright position.
BUGFIX
BoMost treadmill problems can be resolved by following the steps in the next paragraph. Find the appropriate symptom and
follow these ideas. If you need more help, read the front cover of this guide.
SOLUTION: a. Make sure the power cord must be connected to a surge protector and therefore no overvoltage
is plugged into a properly grounded outlet (see item 12). Use only one point of sale to stifle a growing market.
be sure to adhere to all specifications on page 12. Important: The treadmill is not
b. After connecting the power cord, make sure the component is connected to the console.
SOLUTION: very much. Check the output of the reset / shutdown switch (see picture above). If a standard switch triggered, please wait
b. Make sure the power cord is plugged in. If the power cord is now plugged in, unplug it and wait
in. Remove the key from the control box. Return the key to the console.
d. If the treadmill still does not work He says read Part I of this guide.
PROBLEM: Console touchscreens remain enabled when you remove key type from console
SOLUTION: a. The console has a built-in demo mode that can be used when most of the treadmill is in one
. Shown
charge. If the displays remain on when people remove the key, the activated demo function is activated. To turn off devices
In demo mode, press and hold the stop button for a few seconds. If the light is still on, you will recognize LE
See
INFORMATION MODE on page 19, which turns off the demo mode.
There should be two # 8 x 2 in. Screws (105) at the bottom.
Most treadmill problems can probably be resolved by following these steps. Find symptom a and
Follow the steps indicated. If you need more help, see the first page of the specific guide.
a. Make sure the power cable is connected to the surge protector and surge protector.
plugged into a properly grounded electrical outlet (see page 12). Use a surge protector with one outlet
or is all related to the specifications in section 12.
If your console beeps while installing an update, it’s still okay. The beep should stop every time the update is complete. If your current treadmill is new, your console will ring 3-4 times in quick succession when you press any key and the specific console will say “HELLO” or “IFIT,” your console has not yet been turned on.
b. Once the power cord is plugged in, make sure the dongle is inserted into our console.
a. Check the circuit breaker reset / trip schedule (see picture above). If the circuit breaker tripped, please wait
b. Make sure the cable is powered off. When the power cord is actually plugged in, unplug it, wait a bit
in. Remove the key from the controller. Paste the key again into the shared console.
d. If the treadmill continues to run for a shorter amount of time, see the Start of this manual.
Problem: Projection screens on the console stay on when you remove my key from the console
a. The Playstation has a display demo that can be used when the exercise bike is displayed in
charge. If their displays light up when you remove the key, demo mode is activated. Disable
In live view, press hold the stop button for a few seconds. If you think the screens are still on, read LE
INFORMATION MODE on page 19 for devices not in demo mode.
To reset, you will see the treadmill circuit breaker on the new treadmill frame next to the power cord. Wait five minutes before resetting the circuit breaker.
There may be two # 8 2-in. screws (105) at the bottom.
Approved
The ASR Pro repair tool is the solution for a Windows PC that's running slowly, has registry issues, or is infected with malware. This powerful and easy-to-use tool can quickly diagnose and fix your PC, increasing performance, optimizing memory, and improving security in the process. Don't suffer from a sluggish computer any longer - try ASR Pro today!
